|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
A-BRIGHT Part Number: 61-23SWC A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Power Sunset White Surface Mount Device Package outlines & Re-flow Profile Reflow Temp/Time Soldering iron Basic spec is 5sec when 260. If temperature is higher, time should be shorter (+10 -1sec ).Power dissipation of iron should be smaller than 15W, and temperatures should be controllable .Surface temperature of the device should be under 230 . ITEM Resin (mold) Lens color Printed circuit board Emitted color For reflow soldering (Propose) Material MATERIALS Epoxy Yellow Diffused BT Sunset White InGaN NOTES: 1. All dimensions are in millimeters (inches); 2. Tolerances are 0.1mm (0.004inch) unless otherwise noted. 3. Polarity referring onto the cathode mark is reversed on the red. A-BRIGHT Part Number: 61-23SWC A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS ELECTRO-OPTICAL CHARACTERISTICS Parameter Viewing angle at 50% IV Forward voltage Luminous intensity Peak pulsing current (1/10 duty f=1kHz) (TA=25) Value MIN. TYP. MAX. Test Condition Symbol IF=10mA IF=20mA IF=60mA 21/2 VF IV IFP Unit Deg 120 2.8 --3.8 V mcd mA 2900 3250 --- 100 Absolute maximum ratings Parameter Forward current Reverse voltage Reverse current Power Consumptoin Operating temperature range Storage temperature range (TA=25) Symbol IF VR IR PC Top Tstg Value 60 5 10 230 -40 ~+85 -40 ~+100 Unit mA V A mW A-BRIGHT Part Number: 61-23SWC A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS CIE Chromaticity Diagram & Color Ranks A-BRIGHT Part Number: 61-23SWC A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Typical Electro-Optical Characteristic Curves A-BRIGHT Part Number: 61-23SWC A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Taping Dimension (Unit=mm) A-BRIGHT Part Number: 61-23SWC Precautions For Use A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. |
Price & Availability of 61-23SWC |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |